# Raspberry Pi 5 Seedstudio XIAO Halow (Qeutecel FGH100M-H **URL:** \ **Category:** Software\ **Created:** [August 17, 2026, 1:33am UTC](https://community.morsemicro.com/t/raspberry-pi-5-seedstudio-xiao-halow-qeutecel-fgh100m-h/1941 "2026-08-17T01:33:02Z")\ **Posts on this page:** 1\ **Showing post:** 3
**Author:** ![Kenbsherman](https://avatars.discourse-cdn.com/v4/letter/k/ea666f/32.png) [@Kenbsherman](https://community.morsemicro.com/u/Kenbsherman)\ **Post date:** [August 17, 2026, 5:22pm UTC](https://community.morsemicro.com/t/raspberry-pi-5-seedstudio-xiao-halow-qeutecel-fgh100m-h/1941/3 "2026-08-17T17:22:37Z")
I updated the hw.c file , recompiled and installed and the error messages did not change. The seedstudio board side of the wired connections didn’t seem solid so I soldered those sides on and double checked the wiring. I do see some different messages. [4.665053] Morse Micro Dot11ah driver registration. Version 0-rel\_mm8108\_2\_0\_0\_2026\_Apr\_21 [4.665062] channelization\_scheme = 3 (IEEE802.11-REVmf) [5.001060] Adding 2097136k swap on /var/swap. Priority:-2 extents:2 across:2228208k SS [5.083921] morse micro driver registration. Version 0-rel\_mm8108\_2\_0\_0\_2026\_Apr\_21 [5.084008] morse\_spi spi0.0: morse\_of\_probe: Reading gpio pins configuration from device tree [5.084036] Resetting Morse Chip [5.104055] Done [5.115372] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [5.115378] Bluetooth: BNEP filters: protocol multicast [5.115383] Bluetooth: BNEP socket layer initialized [5.184334] uaccess char driver major number is 509 [5.184455] morse\_io: Device node ‘/dev/morse\_io’ created successfully [5.203620] morse\_spi spi0.0: Loaded firmware from morse/mm6108.bin, size 459124, crc32 0x51d355b9 [5.212018] morse\_spi spi0.0: Loaded BCF from morse/bcf\_fgh100mhaamd.bin, size 1251, crc32 0x941b2a82 [5.337819] Bluetooth: hci0: BCM: features 0x2f [5.339142] Bluetooth: hci0: BCM43455 37.4MHz Raspberry Pi 3±0190 [5.339144] Bluetooth: hci0: BCM4345C0 (003.001.025) build 0382 [5.339431] Bluetooth: hci0: BCM: Using default device address (43:45:c0:00:1f:ac) [5.356415] Bluetooth: MGMT ver 1.23 [5.360453] NET: Registered PF\_ALG protocol family [5.568438] macb 1f00100000.ethernet eth0: PHY [1f00100000.ethernet-ffffffff:01] driver [Broadcom BCM54213PE] (irq=POLL) [5.568448] macb 1f00100000.ethernet eth0: configuring for phy/rgmii-id link mode [5.571705] macb 1f00100000.ethernet: gem-ptp-timer ptp clock registered. [5.599439] brcmfmac: brcmf\_cfg80211\_set\_power\_mgmt: power save enabled [5.823695] morse\_spi spi0.0: Incompatible FW version: (Driver) 57.3.0, (Chip) 56.3.0 [5.823703] morse\_spi spi0.0: morse\_firmware\_prepare failed: -1 [5.824114] morse\_spi\_probe: probe failed (ret:-1) [5.824119] morse\_spi spi0.0: probe with driver morse\_spi failed with error -1 the firmware came from git clone [GitHub - MorseMicro/morse-firmware · GitHub](https://github.com/MorseMicro/morse-firmware.git) --branch 1.16 morse drivers from git clone [GitHub - MorseMicro/morse\_driver · GitHub](https://github.com/MorseMicro/morse_driver.git) also kbsherman@pi5:~ $ cat /etc/modprobe.d/morse.conf options morse bcf=bcf\_fgh100mhaamd.bin there’s a thread on [Incompatible, Chip and Driver](https://community.morsemicro.com/t/incompatible-chip-and-driver/1223) that makes a few suggestions but it’s not clear to me if these suggestions make sense. I rolled back the changes to hw.c and the error messages stay the same. I am powering the morse module with 3.3v. I’ve seen some other threads suggesting 5 volts but the seed studio spec calls out 3.3v. Looks like the main problem is a firmware / driver mismatch. @ajudge I took a look at the firmware and driver repo and the version numbers in github don’t align with the dmesg versions. What’s the best way to resolve? --- _[View the full topic](https://community.morsemicro.com/t/raspberry-pi-5-seedstudio-xiao-halow-qeutecel-fgh100m-h/1941)._