# Multicast Setting not being set **URL:** \ **Category:** General\ **Created:** [September 11, 2025, 11:37pm UTC](https://community.morsemicro.com/t/multicast-setting-not-being-set/838 "2025-09-11T23:37:31Z")\ **Posts on this page:** 3\ **Page:** 1
**Author:** ![73challenger](https://avatars.discourse-cdn.com/v4/letter/7/8e7dd6/32.png) [@73challenger](https://community.morsemicro.com/u/73challenger)\ **Post date:** [September 11, 2025, 11:37pm UTC](https://community.morsemicro.com/t/multicast-setting-not-being-set/838/1 "2025-09-11T23:37:31Z")
Hello, I have a uci default script running to do some initial config. But, the `enable_mcast_rate_control` setting won’t apply. I do currently have the device configured for 802.11s. Any thoughts on why? I also tried setting it by hand with no luck, rebooted a few times. Also, do you see any other settings that would help my MANET usecase? ```auto #!/bin/sh # Apply defaults for Morse Micro radio0 without overwriting existing settings dev="radio0" uci set wireless.$dev.bcf='bcf_fgh100mhaamd.bin' uci set wireless.$dev.enable_mcast_whitelist=0 uci set wireless.$dev.enable_mcast_rate_control=1 uci set wireless.$dev.country='US' uci commit wireless reload_config # Exit 0 so this script is removed from /etc/uci-defaults after first boot exit 0 ``` ```auto [7.742560] Morse Micro Dot11ah driver registration. Version 0-rel_1_15_3_2025_Apr_16 [7.754829] usbcore: registered new interface driver huawei_cdc_ncm [7.764350] usbcore: registered new interface driver ipw [7.769781] usbserial: USB Serial support registered for IPWireless converter [7.777570] usbcore: registered new interface driver kalmia [7.798218] usbcore: registered new interface driver MOSCHIP usb-ethernet driver [7.809676] morse micro driver registration. Version 0-rel_1_15_3_2025_Apr_16 [7.817174] morse_spi spi0.0: morse_of_probe: Reading gpio pins configuration from device tree [7.826038] uaccess char driver major number is 240 [7.831104] morse_io: Device node '/dev/morse_io' created successfully [7.880515] morse_spi spi0.0: Loaded firmware from morse/mm6108.bin, size 444304, crc32 0x1c6a0f92 [7.889609] morse_spi spi0.0: Loaded BCF from morse/bcf_fgh100mhaamd.bin, size 1251, crc32 0x941b2a82 [8.508753] morse_spi spi0.0: Driver loaded with kernel module parameters [8.515558] morse_spi spi0.0: slow_clock_mode : 0 [8.522705] morse_spi spi0.0: enable_1mhz_probes : Y [8.529845] morse_spi spi0.0: enable_sched_scan : Y [8.536978] morse_spi spi0.0: enable_hw_scan : Y [8.544110] morse_spi spi0.0: enable_pv1 : N [8.551245] morse_spi spi0.0: enable_page_slicing : N [8.558375] morse_spi spi0.0: log_modparams_on_boot : Y [8.565503] morse_spi spi0.0: enable_mcast_rate_control : N [8.572633] morse_spi spi0.0: enable_mcast_whitelist : N [8.579764] morse_spi spi0.0: ocs_type : 1 [8.586893] morse_spi spi0.0: enable_wiphy : 0 [8.594022] morse_spi spi0.0: enable_auto_mpsw : Y [8.601153] morse_spi spi0.0: duty_cycle_probe_retry_threshold : 2500 [8.608544] morse_spi spi0.0: duty_cycle_mode : 0 [8.615672] morse_spi spi0.0: enable_auto_duty_cycle : Y [8.622810] morse_spi spi0.0: dhcpc_lease_update_script : /morse/scripts/dhcpc_update.sh [8.632466] morse_spi spi0.0: enable_ibss_probe_filtering : Y [8.639599] morse_spi spi0.0: enable_dhcpc_offload : N [8.646727] morse_spi spi0.0: enable_arp_offload : N [8.653857] morse_spi spi0.0: enable_bcn_change_seq_monitor : 0 [8.660986] morse_spi spi0.0: enable_cac : 0 [8.668114] morse_spi spi0.0: max_mc_frames : 10 [8.675332] morse_spi spi0.0: tx_max_power_mbm : 2200 [8.682724] morse_spi spi0.0: enable_twt : Y [8.689854] morse_spi spi0.0: enable_mac80211_connection_monitor : N [8.696982] morse_spi spi0.0: enable_airtime_fairness : N [8.704112] morse_spi spi0.0: enable_raw : Y [8.711242] morse_spi spi0.0: max_aggregation_count : 0 [8.718372] morse_spi spi0.0: max_rate_tries : 1 [8.725500] morse_spi spi0.0: max_rates : 4 [8.732630] morse_spi spi0.0: enable_watchdog_reset : N [8.739760] morse_spi spi0.0: watchdog_interval_secs : 30 [8.746975] morse_spi spi0.0: enable_watchdog : Y [8.754107] morse_spi spi0.0: country : US [8.761324] morse_spi spi0.0: enable_cts_to_self : N [8.768454] morse_spi spi0.0: enable_rts_8mhz : N [8.775582] morse_spi spi0.0: enable_trav_pilot : Y [8.782712] morse_spi spi0.0: enable_sgi_rc : Y [8.789842] morse_spi spi0.0: enable_mbssid_ie : N [8.796970] morse_spi spi0.0: virtual_sta_max : 0 [8.804100] morse_spi spi0.0: thin_lmac : 0 [8.811229] morse_spi spi0.0: enable_dynamic_ps_offload : Y [8.818360] morse_spi spi0.0: enable_ps : 2 [8.825487] morse_spi spi0.0: enable_subbands : 2 [8.832617] morse_spi spi0.0: enable_survey : Y [8.839747] morse_spi spi0.0: mcs10_mode : 0 [8.846875] morse_spi spi0.0: mcs_mask : 1023 [8.854265] morse_spi spi0.0: no_hwcrypt : 0 [8.861396] morse_spi spi0.0: enable_ext_xtal_init : N [8.868529] morse_spi spi0.0: enable_otp_check : 1 [8.875657] morse_spi spi0.0: bcf : bcf_fgh100mhaamd.bin [8.884438] morse_spi spi0.0: serial : default [8.892090] morse_spi spi0.0: debug_mask : 8 [8.899220] morse_spi spi0.0: tx_status_lifetime_ms : 15000 [8.906696] morse_spi spi0.0: tx_queued_lifetime_ms : 1000 [8.914087] morse_spi spi0.0: max_txq_len : 32 [8.921306] morse_spi spi0.0: default_cmd_timeout_ms : 600 [8.928611] morse_spi spi0.0: hw_reload_after_stop : 5 [8.935739] morse_spi spi0.0: enable_short_bcn_as_dtim_override : -1 [8.942956] morse_spi spi0.0: fw_bin_file : [8.950000] morse_spi spi0.0: sdio_reset_time : 400 [8.957302] morse_spi spi0.0: macaddr_suffix : 55:bf:15 [8.965040] morse_spi spi0.0: macaddr_octet : 255 [8.972345] morse_spi spi0.0: max_total_vendor_ie_bytes : 514 [8.979650] morse_spi spi0.0: coredump_include : 1 [8.986778] morse_spi spi0.0: coredump_method : 1 [8.993909] morse_spi spi0.0: enable_coredump : Y [9.001040] morse_spi spi0.0: sdio_clk_debugfs : [9.008081] morse_spi spi0.0: spi_use_edge_irq : N [9.015212] morse_spi spi0.0: spi_clock_speed : 50000000 [9.022950] morse_spi spi0.0: enable_mm_vendor_ie : Y [9.030080] morse_spi spi0.0: fixed_guard : 0 [9.037208] morse_spi spi0.0: fixed_ss : 1 [9.044338] morse_spi spi0.0: fixed_bw : 2 [9.051474] morse_spi spi0.0: fixed_mcs : 4 [9.058605] morse_spi spi0.0: enable_fixed_rate : N ``` ---
**Author:** ![james.haggerty](https://avatars.discourse-cdn.com/v4/letter/j/c68b51/32.png) [@james.haggerty](https://community.morsemicro.com/u/james.haggerty)\ **Post date:** [September 15, 2025, 1:24am UTC](https://community.morsemicro.com/t/multicast-setting-not-being-set/838/2 "2025-09-15T01:24:21Z")
Our apologies; there’s a bug in the current github release which means enable\_mcast\_rate\_control is not being passed through to the driver. To fix this, open /lib/netifd/wireless/morse.sh on your device (e.g. in nano or vi) and add enable\_mcast\_rate\_control to the MM\_MOD\_BOOL environnment variable, then run `wifi up` to force a reload. ---
**Author:** ![73challenger](https://avatars.discourse-cdn.com/v4/letter/7/8e7dd6/32.png) [@73challenger](https://community.morsemicro.com/u/73challenger)\ **Post date:** [September 15, 2025, 1:48am UTC](https://community.morsemicro.com/t/multicast-setting-not-being-set/838/3 "2025-09-15T01:48:58Z")
Thank you! I knew I wasn’t crazy 🙂